ST STE Scanlines
THIS PAGE IS A DRAFT. IT'S NOT LINKED TO FROM ANYWHERE IN THE WIKI YET.
Troed / SYNC
The following is a pseudo code description of how the circuitry involved in creating scanlines, including sync pulses and displaying of pixel data, functions in the Atari ST and STE. By following the logic described here it's possible to implement emulators and simulators that will be able to run existing Atari ST and STE programs that make use of "sync tricks" to create fullscreens and sync scrollers.
Disclaimer: This page has as a goal to contain everything that's currently known, but by no means it should be considered complete.
Information used to create these tables has mostly been sourced from the people below, but a general thanks goes out to everyone who's ever written anything on the subject.
- Alien of ST Connexion (Overscan Techniques part I and II) [1] [2]
- Paulo Simoes (posts on Atari-Forum, wakestate discovery and ST documentation) [3]
- Dio (posts on Atari-Forum, trace diagrams, DE-to-LOAD) [4]
- Troed of SYNC (GLUE-CPU wakestate hypothesis, STE pre-fetch impact) [5]
GLUE state machine, ST
Due to lack of synchronisation between GLUE and CPU when an ST is powered on both chips, while running at 8MHz, can be offset from each other. This is the hypothesised cause behind what's known as ST "wakeup modes" (where two were known and documented beginning 2006 [6]) and more recently divided into two more making four in total, now known as "wakestates" (2013) [7].
At each cycle in the table below, as seen by the CPU, the value can be offset 0-3 cycles set when the ST is powered on. This offset does not change when reset, only when powered off and on again. While this looks like an emulator/simulator needing to be one-cycle accurate to fully capture these modes it's as far as currently known not needed. Since sync tricks can only be made with a resolution of two cycles (by using EXG+MOVE and similar instructions) it's possible to emulate all tricks with two cycle emulation granularity as well.
| VAR H | H signal as per Alien's doc, combines with V and becomes DE detected by MMU |
| VAR LINE | (LORES) NTSC by default; PAL = 512 cycle 50Hz, NTSC = 508 cycle 60Hz, HIRES = 224 cycle 71Hz |
| VAR RES | $ff8260, 0 = LO, 2 = HI |
| VAR FREQ | $ff820a, 0 = 60, 2 = 50 |
| VAR BLANK | Activate blank if true. When BLANK is set no RES/FREQ checks are made (or simply no DE changes?) |
| VAR HSYNC | Activate hsync if true, will also deactivate H |
| Cycle | Action |
|---|---|
| 4 | IF(RES == HI) H = TRUE |
| 30 | IF(RES == LO) BLANK = FALSE |
| 52 | IF(FREQ == 60) && (RES == LO) H = TRUE |
| 54 | IF(FREQ == 50) LINE = PAL |
| 56 | IF(FREQ == 50) && (RES == LO) H = TRUE |
| 164 | IF(RES == HI) H = FALSE |
| 184 | IF(RES == HI) BLANK = TRUE |
| 372 | IF(FREQ == 60) && (RES == LO) H = FALSE |
| 376 | IF(FREQ == 50) && (RES == LO) H = FALSE |
| 450 | IF(RES == LO) BLANK = TRUE |
| 462 | IF(RES == LO) HSYNC = TRUE && H = FALSE |
| 502 | IF(RES == LO) HSYNC = FALSE |
Due to the internal workings of the GLUE, cause unknown, all state checks of the RES register are made one cycle later than FREQ. This is best described with an example using position 56 in the table above:
- Offset 0 reads values at cycle 56 (FREQ) and 57 (RES)
- Offset 1 reads values at cycle 57 (FREQ) and 58 (RES)
- Offset 2 reads values at cycle 58 (FREQ) and 59 (RES)
- Offset 3 reads values at cycle 59 (FREQ) and 60 (RES)
The above, as seen by a program running on the CPU, means that to be able to change the values of the registers for the GLUE to pick them up in the current wakestate they need to have been done at the following cycles:
- WS1 (DL6): Changes made by 56 (FREQ), 56 (RES)
- WS3 (DL5): Changes made by 56 (FREQ), 58 (RES)
- WS4 (DL4): Changes made by 58 (FREQ), 58 (RES)
- WS2 (DL3): Changes made by 58 (FREQ), 60 (RES)
As can be seen above these four different combinations have been given their own numbering - they are the four known wakestates. Any program that needs to do detailed sync manipulation, depending on how detailed, needs to detect which wakestate the ST is in and modify its timing. Since wakeup modes were only documented and detected in 2006, some classic demos shows such side effects. The TCB "tv-snow" screen in Swedish New Year Demo has a disting logo that's only centered in wakestate 2 - in all the others it's offset to the left. [8]
The DL3-DL6 moniker in parenthesis above is another way to name the wakestates, after how long the delay is between the GLUE raising DE (Display Enable), which it does one cycle later than the checks described above, and the MMU detecting it [9]. This has also the side effect of the wakestates being physically offset on screen by one pixel from eachother - WS2 (DL3) leftmost and WS1 (DL6) rightmost. This is caused by monitors using HSYNC to place the screen and depending on wakestate the distance between the HSYNC pulse and the displayed pixels differs.
GLUE state machine, STE
In the STE the GLUE and MMU were combined into a single circuit, the GST MCU. This also meant that the GLUE and CPU were no longer offset by 0-3 cycles as on the ST but fully synchronised at 0. Thus there are no GLUE wakeup modes/wakestates known on the STE. Several changes were however made to accommodate hardware scroll support where one of the more notable ones was an earlier check for starting the screen in high res (= left border) which caused many older border removing demos to fail.
| VAR H | H signal as per Alien's doc, combines with V and becomes DE detected by MMU |
| VAR LINE | (LORES) NTSC by default; PAL = 512 cycle 50Hz, NTSC = 508 cycle 60Hz, HIRES = 224 cycle 71Hz |
| VAR RES | $ff8260, 0 = LO, 2 = HI |
| VAR FREQ | $ff820a, 0 = 60, 2 = 50 |
| VAR BLANK | Activate blank if true. When BLANK is set no RES/FREQ checks are made (or simply no DE changes?) |
| VAR HSYNC | Activate hsync if true, will also deactivate H |
| Cycle | Action |
|---|---|
| 0 | IF(RES == HI) H = TRUE |
| 4 | IF(RES == LO && H == TRUE) SUBTRACT 6 BYTES FROM LEFT BORDER (= +20) |
| 28 | IF(RES == LO) BLANK = FALSE |
| 36 | IF(FREQ == 60) H = TRUE |
| 40 | IF(FREQ == 50) && (RES == LO) H = TRUE |
| 44 | IF(RES == HI && H == TRUE) SUBTRACT 2 BYTES FROM PREFETCH (= +6) |
| 48 | IF(RES == HI && H == TRUE) SUBTRACT 4 BYTES FROM PREFETCH (= +4) |
| 54 | IF(FREQ == 50) LINE = PAL |
| 56 | SYNC-pos - must be LO |
| 164 | IF(RES == HI) H = FALSE |
| 184 | IF(RES == HI) BLANK = TRUE |
| 372 | IF(FREQ == 60) H = FALSE |
| 376 | IF(FREQ == 50) && (RES == LO) H = FALSE |
| 448 | IF(RES == LO) BLANK = TRUE |
| 460 | IF(RES == LO) HSYNC = TRUE && H = FALSE |
| 500 | IF(RES == LO) HSYNC = FALSE |
It's likely that the +20, +4 and +6 cases above caused by switching mode during pre-fetch are in reality made in the Shifter, which has it's own copy of the RES register. This will be investigated further when documenting the Shifter state machine and the inclusion here is to be seen as for the time being.
MMU state machine
| VAR H | Same signal as raised by GLUE above (it's actually combined with V forming DE) |
| VAR DE | DE as detected by the MMU |
Note: These cycle timings are NOT affected by wake states on ST
To be updated: 2 cycle later detection or later raised DE from GLUE? Also rewrite as DE and LOAD.
| Cycle | Action |
|---|---|
| 8 | IF(H == TRUE) DE = TRUE |
| STE 40 | IF(H == TRUE) DE = TRUE* |
| STE 44 | IF(H == TRUE) DE = TRUE* |
| STF 56 | IF(H == TRUE) DE = TRUE |
| STF 60 | IF(H == TRUE) DE = TRUE |
| 168 | IF(H == FALSE) DE = FALSE |
| 376 | IF(H == FALSE) DE = FALSE |
| 380 | IF(H == FALSE) DE = FALSE |
| 468 | IF(H == TRUE) DE = FALSE |
STE due to its capability for hardscroll raises signal H 16 cycles earlier to pre-fetch pixel data, but the prefetched pixels are only displayed if additional registers are set. However, it's possible to manipulate the prefetched data on regular lines to create +20 (left border), +6 and +4 (regular lines) regardless.
MMU detects GLUE DE at cycle 62 and raises LOAD at cycle 64. From this we can calculate the DL-moniker [10] for the ST wakestates depending on when GLUE raised DE:
- 64-58 = 6 = DL6
- 64-59 = 5 = DL5
- 64-60 = 4 = DL4
- 64-61 = 3 = DL3
After LOAD it takes 16 cycles, plus 2 due to internal delays, for the Shifter to set the first values on the RGB pins.
Shifter state machine
TBD
Regular sync scrolling is made with changes affecting GLUE. 4-pixel sync scrolling as well as the cause for "stable" and "unstable" sync lines is due to Shifter.
Sync line lengths
Sync scrollers are created by combining scanlines of different lengths, as read in bytes, to cause the displayed screen to be offset by a chosen amount. It's possible to calculate the amount of bytes lines created by modifying the FREQ and RES registers in GLUE use as follows (see the GLUE state machines for the specific actions needed):
| Bytes | Method |
|---|---|
| 0 | DE never activated |
| 54 | DE activated at 60, deactivated at 168. (168-60)/2 = 54 |
| 56 | DE activated at 56, deactivated at 168. (168-56)/2 = 56 |
| 80 | DE activated at 8, deactivated at 168. (168-8)/2 = 80 |
| 158 | DE activated at 60, deactivated at 376. (376-60)/2 = 158 |
| 160 | DE activated at 56, deactivated at 376. (376-56)/2 = 160 |
| 160 | DE activated at 60, deactivated at 380. (380-60)/2 = 160 |
| 162 | DE activated at 56, deactivated at 380. (380-56)/2 = 162 |
| 184 | DE activated at 8, deactivated at 376. (376-8)/2 = 184 |
| 186 | DE activated at 8, deactivated at 380. (380-8)/2 = 186 |
| 204 | DE activated at 60, deactivated at 468. (468-60)/2 = 204 |
| 206 | DE activated at 56, deactivated at 468. (468-56)/2 = 206 |
| 230 | DE activated at 8, deactivated at 468. (468-8)/2 = 230 |
The above examples are PAL, as most demos use. It's however equally easy to calculate how wide (in bytes - multiply by two to get pixels) a left border would be in NTSC compared to PAL:
- DE activated at 8 compared to regular NTSC line at 56. (56-8)/2 = 24 bytes
- DE activated at 8 compared to regular PAL line at 60. (60-8)/2 = 26 bytes
And a right border:
- DE deactivated at 468 compared to regular PAL line at 380. (468-380)/2 = 44 bytes
- DE deactivated at 464 compared to regular NTSC line at 376. (464-376)/2 = 44 bytes
- Note: An NTSC line is 508 cycles instead of 512 so the deactivation due to HSYNC will happen at 464
Paulo has written a test program for ST that displays many of the possible combinations, attached to a forum post here: [11]
Clean vs sync disrupting
Some effects possible to make by changing state of the GLUE also cause changes to the signals BLANK and HSYNC. Depending on how forgiving the monitor/TV set used is these effects might seems fully working, or cause "bent" lines or discolorisation of parts of the screen. As a general rule these signals should not be modified, but since they have been in demos this is a brief documentation of their effects (timings used are ST, see STE state machine for counterparts):
- Delaying BLANK at 450 - caused by the use of HI/LO stabilizer at 444/456. Additional pixel data, if existing, will be displayed and could cause sync signal disruption.
- Cancelling HSYNC at 462 - black line (no pixels shown) and disrupted sync signal if right border wasn't removed
- Cancelling HSYNC at 462 - fully displayed line with disrupted sync signal if the right border had been opened, Display Enable constantly set. This is done by mistake by the initialization code in the game Enchanted Lands by TCB [12]
- Extending HSYNC at 502 - 0 byte line and disrupted sync signal.
- Extending BLANK at 30 - 0 byte line and disrupted sync signal.
It's possible (currently untested) that using MID/LO stabilizer at 440/456 (also known as "ULM stabilizer") won't delay BLANK. For the other cases there are other ways to black out a line as well as creating 0 byte lines that do not disrupt sync.
Future research / Incomplete
- The "just blank" lines possible to create with switches of both RES and FREQ. They're documented for both ST and STE, but there's no cause known for why they happen yet.
- the 14 byte line (RES = HI at cycle 32 will cause HSYNC which will cancel DE 4 cycles later. (36-8)/2 = 14) (disrupts sync and shouldn't be used anyway)
- Shifter state machine